Table of Contents
Storage Hardware Recommendations
TetherBox recording can run continuously, 24/7. Select drives for sustained writes, the required retention and the intended service life. A large capacity or a fast interface alone does not establish suitability.
For overall capacity planning, see TetherBox Recording Capacity. For base units that require external storage, see External Storage Required. For sizing the rest of the unit, see Hardware Specifications.
SSDs
Choose TLC NAND with DRAM and high TBW (Terabytes Written) endurance. Avoid QLC and DRAM-less SSDs for these recording configurations. Aim for at least 600 TBW per TB, then check the actual recording writes over the intended service life; meeting that ratio alone is insufficient. Larger capacities do not always scale endurance linearly. Provide airflow, especially for high-performance NVMe models.
Prefer professional NAS or enterprise storage for recording. Check the exact model and capacity's datasheet for NAND, DRAM, endurance, warranty and any required power-loss protection; a product name alone does not establish those features.
SSD Write Endurance
An SSD's endurance is the total data its manufacturer rates it to accept over its life, in TBW (terabytes written). The drive counts how much of that it has used and reports it as a percentage, which TetherX shows on the drive's page. Above 100%, the drive has used its rated endurance. It may keep working, but it is past what its manufacturer rates it for, so TetherX shows a warning. Plan to replace it with a drive whose TBW covers the recording writes for the intended service life, using the guidance above.
Enterprise SATA Recording SSDs
Kingston's DC600M / DC600ME manufacturer datasheet (opens in a new tab) explicitly specifies 3D TLC, DRAM and hardware power-loss protection. These 2.5-inch SATA drives suit mixed-use server workloads; DC600ME adds AES-256/TCG Opal encryption, without increasing the listed endurance.
| Models | Advertised capacity | Binary equivalent before formatting | Rated endurance | Published write workload |
|---|---|---|---|---|
| SEDC600M/1920G or SEDC600ME/1920G | 1,920 GB / 1.92 TB | About 1,788 GiB / 1.75 TiB | 3504 TBW | 1 full drive write/day for five years |
| SEDC600M/3840G or SEDC600ME/3840G | 3,840 GB / 3.84 TB | About 3,576 GiB / 3.49 TiB | 7008 TBW | 1 full drive write/day for five years |
| SEDC600M/7680G or SEDC600ME/7680G | 7,680 GB / 7.68 TB | About 7,153 GiB / 6.98 TiB | 14016 TBW | 1 full drive write/day for five years |
Advertised capacities use decimal GB/TB; the GiB/TiB column shows binary equivalents before formatting and reserved filesystem space. Enterprise capacities such as 1.92 TB are actual model sizes, rather than 2 TB drives converted to binary units.
The warranty is conditional on time and wear limits. Check the intended workload and local warranty before ordering. A USB enclosure must qualify independently; a suitable SSD does not make its USB bridge reliable. Enterprise and client TBW ratings may use different JEDEC workloads, so they are not a direct performance comparison.
Enterprise U.2 NVMe Recording SSDs
The Kingston DC3000ME (opens in a new tab) 7.68 TB model combines 3D eTLC NAND, onboard DDR4 DRAM (opens in a new tab) and hardware power-loss protection. Its manufacturer datasheet (opens in a new tab) gives the capacity-specific write endurance below.
| Model | Advertised capacity | Binary equivalent before formatting | Rated endurance | Published write workload |
|---|---|---|---|---|
| SEDC3000ME/7T6 | 7,680 GB / 7.68 TB | About 7,153 GiB / 6.98 TiB | 14016 TBW | 1 full drive write/day for five years |
This is a U.2, 2.5-inch, 15 mm PCIe 5.0 x4 drive, backward-compatible with PCIe 4.0 hosts. It needs a suitable NVMe backplane or PCIe adapter and direct airflow; it does not connect directly to an M.2 socket or a SATA-only USB enclosure. Allow for its published 8 W idle and up to 24 W write power when choosing the chassis and cooling.
NAS M.2 NVMe Recording SSDs
The WD Red SN700 uses TLC NAND and onboard DRAM (opens in a new tab) for sustained NAS workloads. The manufacturer's product brief (opens in a new tab) gives these capacity-specific endurance ratings:
| Model | Capacity | Rated endurance |
|---|---|---|
| WD Red SN700 WDS200T1R0C | 2 TB | 2500 TBW |
| WD Red SN700 WDS400T1R0C | 4 TB | 5100 TBW |
These are PCIe 3.0 x4 M.2 2280 drives. The 4 TB version is double-sided, so check clearance and provide appropriate cooling. The SN700 does not have hardware power-loss protection (opens in a new tab); use a suitable enterprise model where that protection is required.
Premium Client NVMe Examples
These client-tier TLC/DRAM models suit a separate boot drive. Before using one for recordings, check its write life, sustained performance and power-loss recovery against the full recording workload.
| Model and manufacturer specification | Capacity | Rated endurance |
|---|---|---|
| Kingston KC3000 (opens in a new tab) | 512 GB | 400 TBW |
| Kingston KC3000 | 2 TB | 1600 TBW |
| Kingston KC3000 | 4 TB | 3200 TBW |
| Samsung 990 PRO (opens in a new tab) | 1 TB | 600 TBW |
| Samsung 990 PRO | 2 TB | 1200 TBW |
| Samsung 990 PRO | 4 TB | 2400 TBW |
| Samsung 9100 PRO (opens in a new tab) | 4 TB | 2400 TBW |
| Samsung 9100 PRO | 8 TB | 4800 TBW |
The 9100 PRO adds PCIe 5.0 performance and an 8 TB option, but its 4 TB endurance matches the 990 PRO's 4 TB rating. Peak interface speed alone is not a reason to pay more for recording storage.
Crucial availability: Micron ended Crucial consumer shipments in February 2026 (opens in a new tab), with warranty service and support continuing. Check the exact model's endurance, new-stock availability and local warranty before buying remaining inventory.
Boot SSD and Recording SSD
A separate boot SSD can be smaller than the recording storage. Approximately 480-512 GB is a practical budget option for a custom build; a 1 TB boot drive is not mandatory. Check the exact capacity's endurance and price, rather than assuming the smaller model is cheaper.
A single SSD for both the operating system and recordings can reduce parts cost when shorter retention is acceptable. It must meet the full recording write workload as well as system writes. Reserve space for the operating system, snapshots and free space when calculating retention. For the installation layout, see Build a TetherBox on Your Own Hardware.
Hard Drives
HDDs remain cost-effective for large-capacity deployments. Use 24/7-rated NAS, surveillance or enterprise CMR drives, sized for the complete read/write workload. Standard and professional product families are different tiers; "Purple" or "SkyHawk" alone does not identify the higher-workload model.
Professional NAS and Surveillance Ranges
Choose from the professional ranges below, checking the exact model's capacity, recording technology, RPM, workload and warranty.
| Manufacturer | Professional NAS | Professional surveillance / AI |
|---|---|---|
| Seagate | IronWolf Pro (opens in a new tab): up to 550 TB/year | SkyHawk AI (opens in a new tab): up to 550 TB/year |
| Western Digital | WD Red Pro (opens in a new tab): up to 550 TB/year | WD Purple Pro (opens in a new tab): up to 550 TB/year |
| Toshiba | N300 Pro (opens in a new tab): up to 550 TB/year | S300 Pro and S300 AI (opens in a new tab): 300 and 550 TB/year respectively |
Five-year warranties are available in these professional tiers, but older and channel-specific variants can differ. For example, Seagate's support page lists a three-year warranty for SkyHawk AI ST18000VE002. Confirm the exact SKU's local terms; a worldwide listing does not establish regional stock. Standard IronWolf, SkyHawk, WD Red Plus, WD Purple and N300 can suit lighter workloads when the exact model qualifies, but are not interchangeable with the professional tier.
Warning: Toshiba's current Asia-Pacific comparison lists standard S300 as SMR, while S300 Pro and S300 AI are CMR. Do not choose standard S300 from its surveillance branding alone. Verify the exact model's recording technology.
Toshiba introduced S300 AI in November 2025, adding a 550 TB/year surveillance option above S300 Pro. Seagate added 32 TB SkyHawk AI, IronWolf Pro and Exos models in January 2026 (opens in a new tab). Choose capacity for retention rather than buying the largest model by default.
SMR Hard Drives
A conventional magnetic recording (CMR) drive writes each track separately. A shingled magnetic recording (SMR) drive overlaps its tracks like roof shingles to fit more on each platter, so it cannot rewrite one track without disturbing the next. Desktop and low-cost SMR drives manage this themselves: they take new writes into a cache area, then rewrite whole bands of tracks to put the data in place while the drive is idle. Western Digital describes these drives as preferring idle time for that background work, and recommends CMR for write-intensive workloads (WD Red statement, 23 June 2020 (opens in a new tab)).
Continuous recording leaves an SMR drive no idle time. Once its cache is full, its writes stall while it rewrites bands, and a stalled recording drive can leave gaps in footage. Use a CMR drive for recording.
How TetherX shows an SMR drive
- The TetherBox's Storage tab shows an SMR drive badge beside the drive's model. Select it for the explanation.
- The drive's page lists its Recording technology: CMR, SMR, possibly SMR, or unknown, with a link to the list that decided it.
- An SMR drive, or a drive of 5400 RPM or slower, working above 50% utilisation is marked Overloaded. The finding names both reasons when both apply.
TetherX decides the recording technology from the drive's model, using the manufacturers' own published lists and the smartmontools drive database (opens in a new tab), which labels SMR families from those lists. "Possibly SMR" means the hard drive reports TRIM support, which SMR drives can use, but no manufacturer's list includes the model. "Unknown" means no list includes the model; it does not mean the drive is CMR.
Checking a model yourself
The manufacturers publish which of their drives use SMR:
- Seagate: CMR and SMR hard drives (opens in a new tab) (read 13 November 2026). It lists 3.5-inch BarraCuda 4 TB and 8 TB, Archive 8 TB, 2.5-inch BarraCuda 2 TB and 4 TB, and 2.5-inch FireCuda 1 TB and 2 TB as SMR. IronWolf, IronWolf Pro, SkyHawk and SkyHawk AI have no SMR models.
- Western Digital: SMR drives by capacity (opens in a new tab) (7 July 2020). WD Red 2 TB to 6 TB (WD20EFAX, WD30EFAX, WD40EFAX, WD60EFAX), WD Blue WD20EZAZ and WD60EZAZ, WD Blue 2.5-inch WD10SPZX and WD20SPZX, and WD Black 2.5-inch WD5000LPSX and WD10SPSX are SMR. WD Red Plus, WD Red Pro and WD Purple are CMR.
Toshiba: Use of SMR in Toshiba consumer hard drives (opens in a new tab) (28 April 2020). P300, DT02 and DT02-V at 4 TB and 6 TB, and L200 and MQ04 at 1 TB and 2 TB, are SMR. The N300 does not use SMR. See also the S300 warning above.
Other models: TetherX also uses an exact model's own datasheet or manual where it states the recording technology, for example the BarraCuda 2.5-inch ST1000LM049 manual (opens in a new tab) (SMR). Where the manufacturer publishes nothing, as for the drives inside some external USB drives, it uses a dated independent list such as HDDScan's list of WD SMR drives (opens in a new tab) (updated 3 July 2021), and the drive's page links the source.
These lists describe the manufacturers' ranges on the dates shown. Check the exact model number, not only the family name. To replace an SMR drive, choose a CMR model from the professional ranges above.
Enterprise Alternatives
For higher-capacity or multi-drive builds, also compare Seagate Exos, WD Gold (opens in a new tab) and Toshiba MG (opens in a new tab). Select a CMR model with the appropriate workload rating, power, cooling and warranty. Confirm SATA versus SAS, sector format and controller compatibility; a SAS drive cannot connect directly to a SATA-only motherboard.
An "AI" HDD handles recording and analytics storage traffic. TetherX AI models run on the CPU or an accelerator; size that processing separately from the drive's published stream and workload ratings.
Capacity and Annual Workload
Check the exact HDD model's CMR recording technology, RPM, annual workload rating and warranty. A NAS or surveillance family name alone does not establish these specifications. For a 20-30-camera budget build, use 7200 RPM CMR; if no suitable 2 TB model is available, compare suitable 4 TB models rather than substituting a slower drive.
Two compact-build specification examples from Seagate's exact-capacity datasheet (opens in a new tab) are:
| Model | Capacity | Recording / speed | Annual workload | Limited warranty |
|---|---|---|---|---|
| IronWolf Pro ST2000NT001 | 2 TB | CMR, 7200 RPM | 550 TB/year | Five years |
| IronWolf Pro ST4000NT001 | 4 TB | CMR, 7200 RPM | 550 TB/year | Five years |
These are manufacturer specifications, not a claim that the 2 TB model is locally stocked. Older NE models can have different workload limits despite similar family names. The regional demo build examples use verified local offers and calculate the retention of their selected 4 TB disk.
Annual workload is independent of retained capacity:
Annual writes (TB) = total daily writes (GB) × 365 / 1000
Include video and snapshot writes, then allow for playback reads and other transfers when checking the manufacturer's workload rating. Deleting old footage does not undo those writes.
For example, 24 cameras continuously recording at 2.048 Mbit/s write about 530.84 GB/day, or 193.76 TB/year, for video alone. A drive rated for 180 TB/year is insufficient for that example even if its capacity meets retention. Add snapshots and read traffic before selecting a suitable higher-workload NAS Pro, surveillance AI/Pro or enterprise CMR drive. Motion-based recording has a different workload; calculate it from the intended recording activity. See Calculate Retention Before Ordering.
Drive Workload Rating
A hard drive's workload rating is the amount of data its manufacturer designs it to transfer in a year, counting both what is written to it and what is read from it. Seagate, Western Digital and Toshiba publish it in TB per year for each model, for example 55 TB/year for a desktop BarraCuda, 180 TB/year for an IronWolf or WD Purple, and 550 TB/year for the professional ranges above. It is not a capacity: a 4 TB drive and a 20 TB drive in the same range usually share the same rating.
Seagate's product manuals state that "workloads exceeding the annualized rate may degrade the drive MTBF and impact product reliability" (IronWolf Pro manual (opens in a new tab)). A drive kept above its rating is therefore more likely to fail before the end of its expected life. Western Digital defines the rating as "the amount of user data transferred to or from the hard drive" (WD Purple product brief (opens in a new tab)), and Toshiba as data "written, read or verified" (MG series datasheet (opens in a new tab)), so reads count as well as writes. Continuous recording makes this easy to exceed. Many cameras may write to one drive. A TetherBox with several drives records each segment into a working area first and then copies it to the drive that keeps it, so when those are different drives, both write every recording. Playback, exports and cloud backup add reads on top.
How TetherX shows it
- When TetherX knows the drive model's rating, the drive's page shows its Annual workload: the data it transferred in a year, averaged over its power-on hours, as written plus read, against its rating, with a link to the manufacturer's specification.
- A drive transferring more than its rating is marked Workload above rating on the Storage tab, on the drive's page and in the TetherBox's health details.
- TetherX reads the figures from the drive's own statistics. It shows nothing for a model whose rating it does not know, or a drive that does not report these statistics, which includes most drives connected over USB. A drive with less than a month of power-on time is not judged, because a few days do not represent a year.
What to do about it
- Record fewer cameras onto the drive, or lower their bitrate. See TetherBox Recording Capacity.
- Add another drive so the recording load is shared between them.
- Replace the drive with a surveillance, NAS or enterprise CMR drive whose rating covers the workload, from the professional ranges above. Calculate the workload the cameras need with the formula above, then add reads.
Slow and Overloaded Drives
A drive of 5400 RPM or slower, or an SMR drive, can fall behind continuous recording. When such a drive is busy for more than half of the time, TetherX marks it Overloaded, naming whether it is the speed, SMR or both. An overloaded drive delays writes, which can leave gaps in recordings and raise the TetherBox's IO wait. Reduce the cameras recording onto it, or replace it with a 7200 RPM CMR surveillance or NAS drive. See Drive Type by Camera Count below and IO Wait and Drive Load.
Drive Type by Camera Count
| Cameras | Recommended Drive Type |
|---|---|
| 1-3 | 4800+ RPM HDD acceptable, SSD preferred |
| 4-8 | 5400 RPM NAS/Surveillance HDD minimum |
| 9-30 | 7200 RPM NAS/Surveillance HDD, or SSD |
| 31-50 | Professional SATA/NVMe SSDs or multiple CMR drives, sized for mixed I/O and retention |
| 51+ | Multiple similarly specified drives; consider RAID5 or RAID6 for load distribution and redundancy |
Tip: The camera-count table is a starting point, not a universal single-drive limit. For larger deployments, calculate sustained writes, snapshot and playback I/O, annual workload and retention, then choose enough drives for that load and the required resilience. RAID5 provides one drive of redundancy and RAID6 provides two; use similarly specified drives and allow for rebuild performance. RAID redundancy does not replace off-site backup.
USB Storage
Use USB 3.0 or faster with a suitable recording drive and its own reliable enclosure. Internal SATA or NVMe remains a straightforward choice where the TetherBox has room for it.
Recommended Enclosure
For a single 3.5-inch SATA recording HDD up to 10 TB, choose the StarTech S351BMU33ET (opens in a new tab). It supports USB 3.0 with UASP, provides a separate power adapter and uses a maintained ON/OFF rocker rather than a momentary soft-power button. StarTech has tested it with 10 TB, 7200 RPM drives.
Leave the rocker ON so it retains its power setting through an outage, and use the supplied power adapter and USB cable. Its manual shows the power control and connection sequence (opens in a new tab). Published multi-unit owner experience from 7 July 2023 (opens in a new tab) reports that this model leaves standby to the drive instead of imposing arbitrary enclosure powerdown or spindown intervals.
For a 2.5-inch SATA recording SSD, add the StarTech 25SATSAS35 carrier (opens in a new tab). It accepts drives up to 15 mm high and presents the standard 3.5-inch dimensions and SATA connector position. Use a SATA drive in this combination; the carrier changes the physical fit, not the storage interface.
The enclosure is fanless. Keep it ventilated and check the recording drive's temperature after installation. This model is for SATA drives; it is not an NVMe enclosure.
Enclosures to Avoid for Unattended Recording
- UGREEN 50423 (opens in a new tab) advertises automatic sleep.
- OWC Mercury Elite Pro Quad (opens in a new tab) automatically spins down without a data signal, according to its manual.
Diagnosing Storage Performance
If a TetherBox shows high load despite being within CPU recommendations, check IO wait. Sustained high IO wait, including readings above 20%, warrants investigating storage performance, health, cabling, USB controllers and RAID activity. It does not identify the failed component by itself. Diagnose the cause before replacing hardware; upgrading the CPU alone does not resolve a storage wait.
For full troubleshooting steps, see IO Wait and Drive Load.
Summary of What to Avoid
- USB memory sticks and SD cards as recording storage for this configuration.
- SMR HDDs for this recording configuration. See SMR Hard Drives.
- Basic desktop HDDs for continuous recording.
- QLC or DRAM-less SSDs, or a capacity whose write rating does not cover the intended service life.
- Unqualified USB adapters/enclosures, soft power controls and automatic sleep/shutdown behaviour.
- USB 2.0 for a new recording-storage installation.
Related Articles
- Hardware Specifications - CPU, RAM, and overall system sizing
- TetherBox Recording Capacity - How much storage you need per camera
- External Storage Required - Setup for base TetherBox units that need an external drive
- Replacing a TetherBox Drive - Physically replacing SSDs, NVMes, and MicroSD cards
- TetherBox Troubleshooting - Diagnosing IO wait, drive issues, and overheating
Referenced in:
- Frequently Asked Questions
- Health Dashboard
- Health Report
- Build a TetherBox on Your Own Hardware
- Pre-Flight Checklist
- TetherBox Deployment Guide
- CPU Recommendations
- Compact TetherBox Demo Build
- External Storage Required
- Hardware Specifications
- Raspberry Pi TetherBox
- Replacing a TetherBox Drive
- Running TetherBox in VirtualBox
- TetherBox Recording Capacity
- TetherBox Troubleshooting